1、平口机的冷切刀切不断怎么办？
1. What about the continuous cold cutting of the flattening machine?
当平口机的冷切刀总是切不断时，要检查切刀是否锋利，是否需要重新磨好；检查上下刀的平衡度是否合适，刀滑块使用久了，磨损有间隙，会导致刀不平衡。
When the cold cutting knife of the flattening machine is always cutting continuously, it is necessary to check whether the cutting knife is sharp and needs to be re-sharpened; check whether the balance of the upper and lower knives is appropriate, the slider of the knife has been used for a long time, and there are gaps in wear and tear, which will lead to the unbalance of the knife.
2、平口机切三条或多条，袋子尺寸长短不一怎么办？
2. Cut three or more pieces of flat-mouthed machine. What about bags of different sizes?
在那一条薄的膜后胶辊上垫上一层，就可以与其他的材料均匀。
A layer on the top roll behind the thin film can be even with other materials.
3、平口机的弹簧断了，是什么原因引起的？
3. The spring of the flattening machine is broken. What causes it?
自粘条没有贴到位，翘起来卷进弹簧，弹簧就会断，在操作中一定要把自粘条贴好。还有一种原因，料不整齐或一坨塞进胶辊，导致弹簧不顺断掉。
If the self-adhesive strip is not in place, the spring will break if it is rolled up and rolled into the spring. In operation, the self-adhesive strip must be affixed well. Another reason is that the springs are broken because of irregular material or a pile of rubber rollers.
4、骨袋制袋机封边两边差异大怎么办？
4. What about the big difference between the two sides of the bony bag making machine?
需将铝压辊调试好，调到封边两边都压得到，就会避免出现这种情况。
It is necessary to adjust the aluminium rollers and press them on both sides of the edge to avoid this situation.
5、印刷袋送料不顺畅，电眼不够敏感怎么办？
5. Printing bags are not smoothly fed and the electric eye is not sensitive enough.
先检查电眼有没有使用正确，电眼对颜色的敏感反应有一定的讲究，如果袋子是单色用蓝色，重色用红色，红色可用于单色、重色。纠边机的电眼底下的辊要喷黑色，如果袋子颜色单一而且较重的话就用白底最好。
First check whether the electric eye is used correctly. The sensitive reaction of the electric eye to color is particular. If the bag is monochrome blue, the heavy color is red, and the red can be used for monochrome and heavy color. The roll under the electric eye of the edge rectifier should be sprayed black. If the color of the bag is single and heavy, the white background is the best.
6、吹膜机出料收卷厚度不匀均，一边薄怎么办？
6. The thickness of discharge and winding of film blower is uneven. What should we do if one side is thin?
需要在薄的一边上在电子架缠上一圈到合适为止。
You need to wrap a circle around the electronic shelf on the thin side until it fits.
7、边封机切出来成品长短不一怎么办？
7. What about the different length of finished products cut out by edge sealing machine?
压簧未压紧导致胶辊打滑，或者后面的夹板夹过紧，需要调试到合适。
Untightened spring causes the cot to slip or the back splint to clamp too tightly, which needs to be adjusted properly.