联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
塑料袋制袋机包括哪些生产工序和注意事项？
一塑料制袋机开机前，必须检查其周围是否有灰尘、杂物，清理干净再操作；并逐个输入制袋的相关数据以及每扎的所需个数；尽量选择色差较大的图案边沿左右调节光眼灵敏度。
Before a plastic bag making machine is started up, it is necessary to check whether there is dust and sundries around it and clean them before operation; input the relevant data of bag making one by one and the number required for each binding; try to select the pattern edge with large color difference to adjust the light eye sensitivity left and right.
二、塑料制袋机主电机先让起低速运转，随即调整边位控制，将膜对分在中间位置；与此同时还要调整制袋机的左、右夹辊，使左右膜对齐，调整前后夹辊，使图案对正。
2. The main motor of the plastic bag making machine starts to run at a low speed, and then adjusts the edge position control to split the film in the middle position; at the same time, adjust the left and right clamping rollers of the bag making machine to align the left and right films, and adjust the front and rear clamping rollers to align the pattern.
三、生产过程中，若是发现全自动制袋机运行有异响或者是温度过高，制袋的质量时好时坏，需要调整。要求质检员进行检验，或者是进行修理，等检验合格后。将生产出来的袋进行整理，并将存在质量缺陷的袋子排除后按规定捆扎好。
III. in the production process, if it is found that the operation of the full-automatic bag making machine has abnormal noise or the temperature is too high, and the quality of bag making is good or bad, it needs to be adjusted. Ask the quality inspector to carry out inspection or repair, etc. after passing the inspection. The produced bags shall be sorted out, and the bags with quality defects shall be bundled as required after elimination.
四、紧接按生产要求上好膜卷，调整好袋的尺寸，安装好热封刀，并初步调好分切刀和热封刀的位置。一切就绪之后就可以打开塑料袋制袋机的电源，按工艺要求设定热封刀温度。
IV. then, roll the film according to the production requirements, adjust the size of the bag, install the heat sealing knife, and preliminarily adjust the position of the cutting knife and the heat sealing knife. After everything is ready, you can turn on the power of the plastic bag making machine and set the temperature of the heat sealing knife according to the process requirements.
五、整个制袋工作完成之后，需要断开塑料袋制袋机的总电源开关，再断开各部位电源开关。工作人员做好清理，保持整洁、良好的状态。
V. after the completion of the whole bag making work, it is necessary to disconnect the main power switch of the plastic bag making machine, and then disconnect the power switch of each part. The staff shall clean up and keep clean and in good condition.
Before a plastic bag making machine is started up, it is necessary to check whether there is dust and sundries around it and clean them before operation; input the relevant data of bag making one by one and the number required for each binding; try to select the pattern edge with large color difference to adjust the light eye sensitivity left and right.
二、塑料制袋机主电机先让起低速运转，随即调整边位控制，将膜对分在中间位置；与此同时还要调整制袋机的左、右夹辊，使左右膜对齐，调整前后夹辊，使图案对正。
2. The main motor of the plastic bag making machine starts to run at a low speed, and then adjusts the edge position control to split the film in the middle position; at the same time, adjust the left and right clamping rollers of the bag making machine to align the left and right films, and adjust the front and rear clamping rollers to align the pattern.
三、生产过程中，若是发现全自动制袋机运行有异响或者是温度过高，制袋的质量时好时坏，需要调整。要求质检员进行检验，或者是进行修理，等检验合格后。将生产出来的袋进行整理，并将存在质量缺陷的袋子排除后按规定捆扎好。
III. in the production process, if it is found that the operation of the full-automatic bag making machine has abnormal noise or the temperature is too high, and the quality of bag making is good or bad, it needs to be adjusted. Ask the quality inspector to carry out inspection or repair, etc. after passing the inspection. The produced bags shall be sorted out, and the bags with quality defects shall be bundled as required after elimination.
四、紧接按生产要求上好膜卷，调整好袋的尺寸，安装好热封刀，并初步调好分切刀和热封刀的位置。一切就绪之后就可以打开塑料袋制袋机的电源，按工艺要求设定热封刀温度。
IV. then, roll the film according to the production requirements, adjust the size of the bag, install the heat sealing knife, and preliminarily adjust the position of the cutting knife and the heat sealing knife. After everything is ready, you can turn on the power of the plastic bag making machine and set the temperature of the heat sealing knife according to the process requirements.
五、整个制袋工作完成之后，需要断开塑料袋制袋机的总电源开关，再断开各部位电源开关。工作人员做好清理，保持整洁、良好的状态。
V. after the completion of the whole bag making work, it is necessary to disconnect the main power switch of the plastic bag making machine, and then disconnect the power switch of each part. The staff shall clean up and keep clean and in good condition.
